FE-DOHC [Archive] - Mazda MX6 Forums: MX6 Forum
PDA

: FE-DOHC

Pages : [1] 2 3 4 5 6 7
  1. Parts
  2. kia sportage flywheel
  3. FE5A Cam Wanted.
  4. Mazda FE3 Turbo with G-series tranny... Best clutch kit to hold power?
  5. Fe3 cams in F8-Dohc ?
  6. What are the best NA mods for the fe3
  7. Chasing twin cam
  8. fe dohc importer
  9. FE3N optical dfizzy
  10. lightweight crankpully: do or don't?
  11. FE3 HLA question
  12. (Kia) FE3 Stoker Starting To Build
  13. MLS headgasket....... woes??
  14. holset H2C on FE3N?
  15. FE SOHC 12v
  16. Where did you get your pistons?
  17. FE/2T-DOHC Rev limit problem
  18. ITB FE3 Miata Dyno
  19. impossible to find. please help!!!!
  20. f8 with ms2....coming soon....
  21. Jumping engine
  22. Spark Blow Out, which plugs ??
  23. Hi Again!!
  24. Another FE3 comes alive...
  25. Spark Plugs for turbo FE-DOHC
  26. FE3 fuel injector question
  27. trade wheels for fe3 engine
  28. Fresh owner of FE3, Immo Problems
  29. Fe3 manual 4wd?
  30. Transmission Handcuff / Brace
  31. Coolant Temp Sensor Part number
  32. 9.2 compresssion ratio
  33. Pistons and Valve train
  34. Opinions please..
  35. FE3 Turbo dyno tuning 3-18-12
  36. Freeze Plug Size
  37. Blew the dust off the car today, took a few short videos
  38. Turbo'ed FE DOHC 929 HB
  39. Fe3n afm help!!
  40. Seeking specs
  41. FE3 2.4 Stroker Kits Avalible
  42. G6 Flywheel to FE-DOHC Conversion Opinion's
  43. Mazda FE-DOHC Facebook page.
  44. FE3t or F2t
  45. KIA FE-DOHC Fuel Rail
  46. NEW INFO*** HLA's
  47. Gearbox numbers
  48. F8 DOHC rebuild help
  49. Mazda FE3-DOHC Drag set up
  50. FE-DOHC Kia Clarus Credos
  51. JDM FE3 install in a 93 Protege
  52. mx6 fe3 with seq COP and seq INJ
  53. My Stroker 2.2 in the build
  54. Megasquirt tune
  55. Straight facepalm
  56. Bringing the FE3 Back, Looking for a set of pistons and race trans
  57. Building N/A Race Motor
  58. cross reference for FE3N 2.0 16v DOHC in 2002 Kia Sportage
  59. FE3 Timing HELP
  60. FE-DOHC Conversion
  61. Crank thoughts
  62. Cams fe3n vs fe5a
  63. Anyone have a stock FE3 intake manifold for sale?
  64. Stripping an SOHC converting to DOHC
  65. How to recognize FE DOHC 103kw from 109kw?
  66. 4g63 pistons and srt4 rods in my fe3
  67. FE-DOHC Miata (6speed/ITB's)
  68. FE DOHC sump
  69. F8 1.8 Intake manifold - Jessie
  70. Fe3 Turbo Conversion
  71. South Africa - interesting read for the FE DOHC fans.
  72. fe3 - no spark and injectors not pulsing
  73. Problems with acceleration. Help!
  74. 4G63 VENOM fuel rail on FE-DOHC
  75. FE3 RWD Setup HELP!
  76. Bearing Plate mod
  77. How much its worth ?
  78. megasquirt choice question about the FE3N
  79. FE3 VS F8 DOHC injector size
  80. ARP Head Studs and Main Studs Numbers
  81. Where to start to import an FE-DOHC
  82. quick update on my cars
  83. Verifying my CAS plans
  84. Turbo for track use
  85. fe3t turbo water lines
  86. Need quick advices about FE ignition and intake
  87. F8-DOHC limits tested! Fail.
  88. Arp Head studs L19
  89. Mazda Fe Dohc with Mazda 3 MPS Gearbox
  90. Second FreeEMS Vehicle Is My Truck!
  91. Wiring... A few simple questions!
  92. FE DOHC Crank Broken
  93. New Today! Lots of questions, lol
  94. FE3 adjustable cam gears round 2
  95. sudden increase in oil pressure
  96. FE3 flywheel
  97. Fe3 lsd
  98. WTB/ Where to find FE3T rwd Turbo mani
  99. FE3 inletmanifold
  100. cams and cam gears
  101. Possible Mod List? What's availible?
  102. Mazda Fe Stroker piston
  103. Mazda Fe Dohc Valves
  104. FE Stroker flywheel
  105. what smaller carb motor fit fe bellhousing
  106. mazda fe dohc R2 crank shaft oil issues
  107. looking to buy fe-dohc engine
  108. f8 swap
  109. Flywheel to engine space
  110. Rx7 Flywheel to fits an fe3
  111. Fe3 head on a G6 B2600
  112. Which FE-DOHC motor option is better? Need some opinions!
  113. mazda Fe VAlves
  114. Pic request: Fred's Bottom End!
  115. coolant routing for turbo???
  116. Fe-ze?
  117. some F8 upgrades
  118. Mazda FE stroker crankshaft
  119. good bye guys!!
  120. FE3 OEM timing xxBTDC???
  121. This is what happens when you install an F2 water pump on an FE3
  122. FE3 round 2
  123. Help finding parts
  124. FE Forged Pistons
  125. some aftermarket parts
  126. turbo manifold for a fe3
  127. is it possible?
  128. what rods for the FE3 stroker?
  129. Speedometer Pinout
  130. Domed Forged Pistons for FE
  131. Pauter rods
  132. mazda fe dohc turbo valve springs
  133. Help me find: FE3 Compatible Bellhousing, i.e. BONGO
  134. FE3 header - where to buy?
  135. How to know is that gearbox from FE dohc
  136. FE3N`s vs FE5A`s
  137. fe3 performance chase
  138. side drafted FE
  139. FE dohc turbo project
  140. Whats this sender unit reading?
  141. 89 mazda 626 rear wheel drv?
  142. power and earth for ecu Fe3
  143. FE3N with stock oil cooler?
  144. FE3 ITB info needed!!!
  145. alternator FE3
  146. fe valve springs
  147. fe valve springs
  148. injectors over fueling
  149. FE3 parts
  150. Exhaust manifold flange FE3
  151. Picture of FE3 Head
  152. Thanks Compnut (or how I has an FE3 now :D)
  153. FE3 powered 323
  154. interchangeable parts with 98 sportage fe3
  155. Oil Pressure sender
  156. intake manifold questions amongst other FE3 questions
  157. Might be going kia FE3... advice?
  158. Want to buy camshaft gears for FE3N
  159. K20 pistons in FE3 Stroker
  160. f2/ fe3 crank? / clutch question
  161. Fe3 turbo HP Numbers
  162. Bellhousing FE3 to RX7 TurboII transmission
  163. FE3 rebuild question!!!
  164. FE3 Wiring diagram / alternator
  165. Rewiring my ms setup, the thread.
  166. FE3 cam regrind advise
  167. Fred needs to check his plugs! :-)
  168. FE3 Oil tank removal
  169. 478PGTs possible FE N/A swap thread.
  170. The Toyota gearbox thread.
  171. holset runners...Fred...I'm looking at you
  172. performance camshafts
  173. FE3 found in a Nissan??
  174. New to the 88 626
  175. Darkcyde's FE3 Adventure
  176. Nissan or Mitsubishi pistons into FE3 ?
  177. 626 88-92 FE3 swap ?
  178. F2T Gearbox with FE3 ?
  179. FE3 Weight?
  180. RWD bell housing differences, slant/straight (new project pics too)
  181. I found stroker1 new build
  182. Destroyed high spec FE3 in junk yard
  183. Evo 9 injector fitment
  184. Quick FE3T update.
  185. How heavey is an FE3 motor
  186. My first good FE3T video ;-) Hold on tight!
  187. FE - F2 Swap
  188. ati damper
  189. fe3 thread disapears??????????,
  190. Question about internals.
  191. Matt's FE3 project
  192. how to make ignition system work using cas for fe3n in b2200
  193. My Fe3 Motor Swap And Build
  194. My fe3 swap
  195. selling all my f3n stuff
  196. max tolerance for decking head?
  197. Billet Cranks
  198. FE DOHC and 3S GE exhaust stud comparison
  199. FE3 a/c bracket that bolts to the block
  200. Good importer western US?
  201. Kia fe-dohc swap into courier
  202. i'm still alive, don't worry
  203. Mazda's gearbox convention
  204. Manifold design for equal cylinder fill
  205. FE3t project in REUNION island
  206. Going top mount
  207. Intake vs. exhaust valve locks - comparison
  208. Turbo or Non Turbo
  209. proper ARP head studs
  210. pistin rings...
  211. splitfire coil packs
  212. Camshafts for FE3??
  213. Where are these 16 valves coming from??
  214. fe3t 626 wagon itbs (56K DUW...lots of pictures)
  215. 400whp on stock pistons and e85?
  216. simple FE3 conversion advice
  217. Norse626 FE3 rebuild, need some advise here.
  218. gearbox question
  219. f2t disty in a fe3
  220. 88 mx6 heater problem
  221. fe3 dohc mx6 swap
  222. Lubrication Problems with a FE3 with stroker
  223. FE3 turbo 626 wagon finally runs
  224. FE3 compression
  225. Should I destroke?
  226. Feeler - Scat Forged rods- who'd be in again???
  227. valve springs
  228. remember evo626?
  229. Fe 3 Rods
  230. my car runs
  231. Is the fe3 under the hood of the kia soul
  232. Farewell FE3t Miata
  233. how to turbo f8 dohc?
  234. Finally Got My B2200.... the fun begins
  235. Which Gearbox to FE DOHC??
  236. vacuum hose routing diagram
  237. Try this again...
  238. Suggested CAM specs but N/A not turbo
  239. Auto raising idle speed problem
  240. Rolled my fidanza cam gears
  241. F8-DOHC turbo dyno
  242. VRIS on Mazda 626
  243. cc'd a fe3n head
  244. bye bye mx6... hello b2200
  245. GI: FE3 4340 Billet Crankshafts
  246. FE3 vs F2 oil pump/head studs....
  247. 2,3 litres with the FE - can it be done?
  248. MX5 in local Mag
  249. My FE-DOHC B2200. MSNS, Slowest thing i own lol
  250. 9.2:1 pistons are they domed??
Terms of Use