official FE3 related items for sale thread - Page 3

**MzdaFrk** · 5-10-06, 13:05

do you have any fwd turbo manifolds? what type of intake plenums do you have, ie: how are they custom? would like to see some pictures.

**89GTowner** · 5-10-06, 14:25

Quote:

Originally Posted by roadcoursemx6

do you have any fwd turbo manifolds? what type of intake plenums do you have, ie: how are they custom? would like to see some pictures.

i second that... also how are the HLAs if u have them???

**fe3t b2200** · 5-11-06, 7:49

nah i dont use hla's got many sets condition unknown! needless to say the mazda hla's so you can bet ya bottom dollar they noisey! i run solid lifters in my engine! can make a fwd turbo manifold for you if you would like have done a few before the majority of my work is rwd how ever! custom inlet plenum is custom to suit application as in my b2200 i have a large wedge shaped plenum with around 5litre capacity and a 76mm throttle body i have some pics of exhaust manifolds i have made if you would like me to email you them i need to take some pics of my plenum as yet!

**MzdaFrk** · 5-11-06, 13:43

info@fastonemotorsports.com, I would like some pictures

**Dutch** · 5-14-06, 5:41

stripped a EURO spec GT. (2.0-16v engine) this was a low spec engine with cat, EGR, and O2 sensor

bare cilinderhead (no cams, no caps, no valves, no nothing

)
camshafts fe3n inlet and exhaust
exhaust manifold
inlet manifold
engine harnes (no cuts, plug and play)
inside car harnes (no cuts, plug and play)
ECU
MAF
probably a lot more... i need to clean out my garage since i got too much FE-dohc's, if u need anything else FE3 related just ask.

please make reasonable offers

note: mind u im in Holland, Europe so shipping can be more expensive then u guys used to, allthough shipping by boat is cheap but takes a while.
see my feedback and service when reading the FST-bar thread.
i can make pics of anything u want.

thanks.

**fredio54** · 5-14-06, 5:53

has your wife got the better of you dutch? ;-)

(he writes as he wirebrushes a flywheel on a persian rug in the lounge)

**Dutch** · 5-14-06, 5:55

she found some camshaft in the living room hidden behind videotapes from my daugher, and the exhaust pipes under the bed became to annoy her. i need space........(and money to finance the finishing of my FE4 and FE3-T)

**MzdaFrk** · 5-14-06, 14:16

My wife got sick of the tires/rims stacked in the bedroom, I had a box of parts sitting on a towel, in our room for a while. I know how it goes!

FE4? I havn't heard fo that before? how much would you want for an Uncut harness and ecu for an FE3? shipping is shipping, I will deal with that.

Rahim_24 · 6-1-06, 19:00

I'm also interested in a uncut wiring harness and Ecu. And just to be on the safe side I need both the inside and outside harness.

**Dutch** · 6-2-06, 12:39

i have both. the in and the outside.. uncut, plug and play.
with ECU and MAF i would sell a set for like 500.- USD.
again .. plug and play and u can start up your FE-dohc.

**MzdaFrk** · 6-2-06, 12:59

ouch, I thought they were like 350, I will have to wait

**ORANGE89pgt** · 6-19-06, 19:02

FE3 engine for sale, it was 88MX6GT (a old member here) old engine that i bought from him last july. here the thread : www.mx6.com/forums/showthread.php?t=130567 (FS: FE DOHC (FE3) fully built for turbo, GT tranny, etc.: see thread for more...)

i bought another project car, soo this engine is up for sale.

1000$ + shiping (should be around 200$) but the motor is built with forged Venolia pistons at 8.5:1 comp ratio. It has 000 miles on it. It has Celvite 77 bearings throughout, Total Seal rings. The injectors are 650CC.

i didnt install it yet, its ben in the garage since i bought it, i put oil in it and turn it manuely every mounth. the only thing is missing is the oil deepstick.

pics http://memimage.cardomain.net/member...72_38_full.jpg

i can get more new pics upon request.
paypal accepted.

more things to come for sale, many parts for the FE3 project that i was building, soo keep an eye here.

**MzdaFrk** · 6-19-06, 19:12

i'll take it! SOLD SOLD SOLD Not missing it again.

**MzdaFrk** · 6-19-06, 19:24

does it have the turbo manifold?

**ORANGE89pgt** · 6-19-06, 21:40

you are the first to pm so its yours.

i have more things that i know you will like, look at your pm.