![]() |
|
|
|
|
#63 (permalink) |
![]() |
lattimus - yes, I have the mounting clips for them as well.
zcm - I'll take some pics of the stuff I have left and post tomorrow. RacerReddyMX6 - Joe, same answer as to zcm. I'll take pics of what I have left and post tomorrow. |
|
mhughes@hickorytech.net for paypal
Shipping address: Mike Hughes, 109 E. LeRay Ave., P.O. Box 363, Eagle Lake, MN 56024 cardomain: http://www.cardomain.com/ride/657895 My website: www.hickorytech.net/~mhughes1 |
|
|
|
|
|
|
#64 (permalink) |
|
Hey, don't suppose you have any black door cards?
|
|
|
Dylan
www.TunerTools.com |
|
|
|
|
|
|
#65 (permalink) |
![]() |
zcm AND RacerReddyMX6 - been so rainy out that I haven't taken the pics yet. Here is what I KNOW I have over there: the black parts that go on the dash (like the glove box, surround, both sides, front tweeter panel, knee panel below the steering wheel). I only have the glove boxes for the 93 (no pass. side airbag cars though). I also have the rear b/c pillar panels and I believe one set of a-pillar panels. I may have some door sills as well as the right and left front kick panels (left side may or may not have the fuse box door included). I also have a couple of the inside door release levers and surrounds. As for interior door panels and rear quarter panel sides, I might have some in black cloth and I know I only have one quarter side in black leather.
Fallen Legacy - see the above response. |
|
mhughes@hickorytech.net for paypal
Shipping address: Mike Hughes, 109 E. LeRay Ave., P.O. Box 363, Eagle Lake, MN 56024 cardomain: http://www.cardomain.com/ride/657895 My website: www.hickorytech.net/~mhughes1 |
|
|
|
|
|
|
#66 (permalink) |
|
yeah pictures would help so I know exactly what I'm looking at. I'm trying to convert to black interior with red accents which I can do myself. I have the whole console (with the vents and stuff and where the shift boot would be) I have that red but the dash I would like to be black. if there's anyway you know of to easily replace it or at least re-skin it that would be pretty tight. I'll post a picture. Also if there is an easy way to replace the leather in the rear panels and the back dash. I was just going to paint the back dash if I can ever figure out how to [fizzle]ing take it off haha.
![]() ![]() Last edited by RacerReddyMX6 : 10-19-08 at 10:34. |
|
|
|
|
|
|
#69 (permalink) |
![]() |
do you have the plastic piece that goes around the door handel on the driver's inside door. I'll try to get a pic because that wasn't very clear.
|
|
1994 MX-6 LS w/ KLZE, chipped ECU, headers, test pipe, Volt muffler, CAI, Outlaw Spacers, Centerforce Stage II clutch, 17" Flik FTD wheels, and black leather interior. http://www.cardomain.com/ride/2616648
1993 Mx-6 LS (RIP) http://www.cardomain.com/ride/2286070 |
|
|
|
|
|
|
#70 (permalink) |
![]() |
Skanetic - I should have one. I'll check while I'm at the storage unit today.
|
|
mhughes@hickorytech.net for paypal
Shipping address: Mike Hughes, 109 E. LeRay Ave., P.O. Box 363, Eagle Lake, MN 56024 cardomain: http://www.cardomain.com/ride/657895 My website: www.hickorytech.net/~mhughes1 |
|
|
|
|
![]() |
| Thread Tools | |
|
|