|Topic Review (Newest First)|
I bought my springs used but they were ordered at 2.5" front and 2.75" drops. I added escort strut mounts up front for more drop because I like it a tad lower up front
It's what I figured, but I was iffy on the engine weight difference. From what I can tell almost every brand sits slightly higher in the rear. I saw someone suggestion to cut one of the "dead" coils off, but I'm not messing with that stuff.
Thanks for answer guys
|friendsofdonr||The fs and kl use the same suspension components. With the exception of the fs/base model having drums instead of rear disc brakes... the fs typically sits higher in the front than a kl because of the difference in engine weight described above. As for the back sitting higher, most manufacturers have recommendations to allow their springs to settle and that guidance should be followed.|
|jrock#1||I have the 2.5 and when I purchased the megan racing springs the site said they were for a 2.0 but the weight difference between the ls and fs is only like 100lbs. The way my car sat after installing them was good even though the rear was slightly higher but I put a ton of weight in the trunk to make it sit level and I’m hoping if I leave it in there long enough the springs will sag to make it sit closer to level.|
|TheGentleArt||Ok, this may sound like a noob question, so I apologize. Is the Megan racing springs applicable to both FS and LS? Every item I found for sale says 2.0 (FS) only, however every other brand would have 2.5 and 2.0 listed, unlike the Megan. I was thinking of doing tokico/Megan, but have been unable to find a place that list the LS as being compatible.|
here's my setup. sorry for the crappy quality. Illuminas with eibachs
This is my set up with kyb gr2 struts and megan racing springs.
The rear sits higher than the front and I'm not sure how to make it sit level. I don't want to cut the springs because I would probably mess it all up. Any ideas?
|Pyramid||Anyone Have photos of a 1.8" drop and 18s? Really want to see how it looks before i do it.|
Originally Posted by Mika-MX6 View Post
|Mika-MX6||KW Variant 3. Solves 2 out of 3 problems that ghost described for the ksports. Dampening functioning actually works all across the range. Threads don't need maintaining as much as the shocks are made out of stainless steel; no rust. Very very very high quality coilover, but you'll have to pay for them. They're about twice the cost of the ksports|
Honestly, I went with the illuminas and megan springs, sticky tires (currently slicks lulz) and a 626 rear sway. This car is absolutely amazing at handling now. Its better than my miata, but the miata is on stock suspension too
Sent from AutoGuide.com Free App
i had ksport on my mx6, i'll just give you an idea of what it's like. i didn't get it to be as low as possible. I got them because I wanted a ride that could turn like hell. and that was exactly what i got.
but first the bad....
the adjustability is moot, because once you get it to your desired height you'll want it to stay there. if u adjust anything you have to do full alignment.
the dampening setting is pretty useless too. you can only go either hardest or max 4 clicks from hard. any softer you'll blow the shocks the first bump you go over. I've replaced 2 shocks over 2 years of ownership of my ksports.
The threads on coilovers are also a maintenance item to keep them from rusting and seizing your spring perches in place. i had to periodically jack the car up and make sure the rings are still tight and re-tighten them if need be.
And the fond memories...
i never regretted lowering my car on ksports... actually maybe i did a little bit when i had to redo everything to replace the shocks. but it was one hell of a ride in the mountains. my Audi A4 quattro on ST coilovers and 22mm rear sway bar definitely wasn't as tight as my old mx6 with the ksports and 22mm rear sway bar in the twisties. the car can turn like hell and i had all sorts of confidence to take banking turns and corners.
if you're just going for the low rider look, and do it cheap, just cut 2 rungs out of your stock springs. (OMG... did i just type that?)
but if you want a car that gets the lowered look and rule the twisties (with a bit of work), do it with ksport coilovers.
|MX6_DeeDz||Depends on how much you want to spend on going low, ksport/d2 same thing, have pillow ball mounts for all the cambers and 32 flavers of adjustability, yonaka uses stock strut mounts and less flavor for adjustability but also cost less. Yonaka coilovers + escort strut mounts would get you the hella flush Jdm yo awesomeness, might have to remove a collar or two though.|
|thatniggakody||hey yall i was wondering if anyone has any suggestions on how to go as low as possible? i cant find many coilovers for my mx.|
Originally Posted by Robert Mull View Post
|This thread has more than 15 replies. Click here to review the whole thread.|